诚信立足、创新致远

Integrity foothold and innovation

全国服务热线:

15356816111

新闻资讯

  • 沙发松动发出响声是什么原因引起的?
  • 本站编辑:杭州余杭壹吉家居有限公司发布日期:2018-08-22 15:48 浏览次数:

2-1F214100914.jpg

沙发坐上去发出响声
The sofa sat up to make a noise.
沙发坐上去发出响声主要原因有三个:沙发木架松动不牢固;沙发坐底的蛇簧与木架发生摩擦发出响声;皮革相互间的摩擦发出响声。
There are three main reasons why the sofa sits up and makes a noise: the sofa wooden frame is loose and unstable; the snake spring on the sofa's bottom rubs against the wooden frame to make a noise; and the leather rubs against each other to make a noise.
1、木架松动有响声首先分清发出响声的地方。如果是木架松动不牢发出响声,看清响声的地方,在发出响声处加钉和加木方。
1, wooden frame loosening noise, first distinguish the place where the noise is produced. If the wooden frame is not loose enough to make a sound, see clearly where the sound is, add nails and wooden cubes at the sound place.
2、坐底蛇簧和木方发生摩擦发出的响声,可把发生摩擦的地方的蛇簧拉开,或是把木方用刀削掉一点,至坐上去没有响声就行。
2. The sound produced by friction between the snake spring and the wooden side can be pulled away from the snake spring where the friction occurs, or the wooden side can be cut off with a knife until there is no sound on the seat.
3、皮革相互摩擦发出响声,可以用皮革保护剂涂在摩擦处,使皮革柔软光滑,这样就不会有摩擦响声。
3. Leather rubs against each other to make a sound. Leather protectant can be applied to the rubbing place to make the leather soft and smooth, so that there will be no rubbing sound.
沙发安装不牢固、松动
Sofa installation is not solid, loose
1、沙发松动主要原因是:沙发在安装时有些受力的地方螺丝拧得不够紧,导致沙发使用一段时间又松动现象;或是沙发孔位太大,导致螺丝拧陷下去,造成松动现象;或沙发在运输过程中,受重物挤压或颠簸而造成松动。
1. Sofa loosening is mainly due to: Sofa installed in some places where the screws are not tightly screwed, resulting in the use of the sofa for a period of time and loosening phenomenon; or the sofa hole is too large, leading to screw down, resulting in loosening phenomenon; or sofa in the transport process, by heavy objects squeezing or bumping caused loosening.
2、如果是螺丝没有拧紧造成,可把螺丝拧紧后,或用自攻螺丝加固。
2, if the screw is not tightened, screw the screws or reinforce them with self tapping screws.
3、如果是孔位太大造成松动,先把陷下去的螺丝松掉,用九厘夹板或木方钻小一点的孔位,放在下陷的孔位上,再加垫片拧紧螺丝就行。
3. If the hole is too big to cause loosening, first loosen the down-to-earth screw, drill a smaller hole with a nine-centimeter splint or wooden square, put it on the down-to-earth hole, and then screw the gasket.